Product Description
Expedition Carbon Monoxide Analyzer.
Analyzer Specification:
- Range: 0-100 ppm
- Accuracy: +/- 2 ppm
- Required Flow: 2 to 4 Lpm
- Alarm: Alarm sounds @ 10 ppm (+/- 1ppm)
- Sensor: Galvanic (Replaceable)
- Response time: 95% @ 10 seconds (May very in extreme temperatures)
- Sensor Expedited life: 3.5 years (Most last 3.5 +)
- Calibration: Only when new sensor installed
- Calibration Interval: Every 3.5 years or replace censor
- Power: 3 ea AAA cells (Alkaline only – User replaceable)
- Battery Life: Varies under continuous use or for immediate sampling
- Operating Temp: 32 degrees F to 120 Degrees F (0C to 50C)
- Storage: 5 Degrees F to 135 Degrees F (-15C to 57C)
- Made In USA
The Expediton CO analyzer reads in parts per million. This truly is a very small amount of CO. The alarm will sound when the level of CO reached 10 PPM (+/- 1ppm).
Most sensors last 3.5 years to 4… we have seen up to 5 years on the sensors. In comparison, you would have to replace two oxygen sensors in an oxygen analyzer during this same time. So the cost of the CO sensor is less over the same time.
The electrolyte in the sensor tends to dry up after 3.5 years. Most sensors are not used up by the actual sampling of CO. The sensors only give off milivolts according to the amount of CO it reads. So the less CO, the longer the life of the sensor.
The OxyCheq Expediton CO analyzer ships in its own case with room for supplied nozzle and room for optional accessories such as a flow restrictor. Please note that all galvanic sensor are susceptible to humidity, temperature and pressure. We recommend a flow restrictor for increased accuracy.
The OxyCheq Expedition CO Analyzer is made in the USA, serviced and calibrated in the USA.
- One Year Warranty on Analyzer and Sensor
- Does not include regulator or calibration gas (Needed when replacing the sensor).
The chart below was taken from customer information and product manuals and may contain inaccuracies. Please report any inaccuracies.
CO Analyzer Comparison |
||
OxyCheq Expedition CO | Analox EII CO | |
Price | $400 MSRP | $355 MSRP |
Replacement Sensor | $140.00 MSRP | $240 to $250 (MSRP / Exchange rate) |
Alarm | Sounds @ 10 PPM +/-1 PPM | No Alarm |
Measurement Range | 0-100 PPM | 1-50 PPM |
Sensor Life | 3.5 + Years | 2 years |
Sensor Accuracy | +/- (1% FS + 1% value) | +/- (1% FS + 5% value) |
Sensor Drift | Less than 0.5 ppm Annually | 6.0 ppm Annually |
Calibration* | When New Sensor Installed or 3.5 years. | Every time used – Prior to every dive with Bump Test |
Hydrophobic Membrane | Yes | No (None Noted) |
Bump Test Required for Calibration | No | Yes ($80 USD) Valid for only 20 Bump test (uses) |
Temperature Compensated | Yes | No (Not noted or found) |
Power | 3 ea AAA | 1 ea 9V |
Battery Replacement | 2-3 years (Occasional Use) 1 year (Inline Compressor Use) |
1 year |
Display | 3 Digits | 2 Digits |
Warranty (Sensor) | 1 year (prorated) | 1 year (prorated) |
Hand Held | Yes | Yes |
Compressor Inline Use | Yes | No |
Continuous Use | Yes | No |
Flow Restrictor (s) | Yes (Optional / Recommended) | No (No Options) |
Purchase price | Analyzer $400 (MSRP) w/ Case Optional Restrictor: $40.00 Total: $440.00 |
Analyzer: $355.00 (MSRP) (No Case) Bump Tester: $80.00 (20 dives) Total: $435.00 |
1 Year Expense | None | Bump Tester: $80 (20 dives) Battery: $1.50 - $3 |
2 Year Expense | Batteries $2 - $4 | Sensor: $240.00 Bump Tester: $80.00 (20 dives) Battery: $1.50 - $3 |
3 Year Expense | None | Bump Tester: $80 (20 dives) Battery: $1.50 - $3 |
4 Year Expense | Sensor $140.00 (3.5 – 4 years) Calibration: ~ $55 Batteries $2 - $4 |
Sensor: $240.00 Bump Tester: $80.00 (20 dives) Battery: $1.50 - $3 |
Total Cost Over 4 years | $600.00 (w/o Flow Restrictor) Does not include batteries ($4 - $8) |
$1235.00 Does not include batteries ($6 - $12) |
Additional Information
SKU | OXY-OA-01-05 |
---|---|
Weight (Lbs) | 1.2000 |
Weight (Kg) | 0.544 |
Manufacturer | OxyCheq |
Country of Manufacture | United States |
Notes | No |